Skip to content
APPROVAL SHEET
| CUSTOMER | |
| SPEC NO | |
| TYPE NO | 5MM60 |
| PART No | |
| DATE | 2025-7-6 |
| CUSTOMER CONFIRMATION OUTCOME OPINION：（） | |
| RESULT： | OK NG |
| COMMENTS： | |
| APPROVAL DATE： | |
| PREPARED BY | CHECKED BY | ACCEPT |
| MAKER： | ||
| PREPARED BY | CHECKED BY | APPROVED BY |
introduce（）
1.The general color rendering number of the artificial standard light source for sunlight and near sunlight is set to 100. The higher the consistency between the color of the same object under the irradiation of the measured light source and that of the standard light source, the larger the Ra, the better the color rendering performance, the smaller the Ra, and the worse the color rendering performance.
2.High color rendering index, uniform light color, high light output efficiency, elimination of violet spectrum, reduce the use temperature of phosphors, improve the consistency and reliability of the spectrum in the long-term use process. Use longer.
3.CRI95 + is the highest display, the true color is restored. Under the contrast of feeling the natural color, the objects presented by the eyes are closer to the natural original flavor.
4.TLCI (> 95) can reflect the degree of color reception and color restoration of the camera. The closer the TLCI value is to 100 degree of color reduction, the better the effect.
- In the CIE1960 coordinate series, the distance of color deviation from the plank trajectory is close to zero,
while all LED light sources produced by Jingjia Electronic Technology Co., Ltd. are compared with the
CIE1960 coordinate series
SSLECO Daylight Series LED Light engine is based on our main patent—– MCOB（Multi-Chips On Board）.
ECO Lighting LEDs combine tens or hundreds power LED chips with a rugged package capable of operating in
excess of power . Smart ECO Lighting LEDs maximumly decrease LED uncomfortable glare and also Zebra strips, at
the same time increase LED light efficency and reduce thermal resistance.
The SSLECO Daylight series consists of near solar spectral light sources with color temperature above 5000K and
black-body radiation spectral light sources with color temperature below 4000K.
Features ：：
◇ Area light source, which can avoid glare
◇ More energy efficient than incandescent , halogen and some fluorescent lamps
◇ Industry’s lowest thermal resistence
◇ Long operating life， lumen maintenance of greater than 70% after 50,000 hours
◇ Low forward voltage operated
◇ Instant light (less than 100ns)
◇ Lead Free product, RoHS compliant
◇ No UV
◇ Natural spectrum:Include Solar Spectrum and Black Body Radiation Spectrum
Application:
◇Schools
◇Libraries
◇Exhibitions
◇Offices
◇Reading rooms
◇Laboratories
◇Hospitals
◇Stadiums
◇Dyeing & Printing
◇Operation lighting
◇Textile workshops
◇Painting workshops
◇Museums
◇Show windows
◇Fresh food stores
◇Markets
◇Photoflood Lamps
◇Art design
Outline Dimensions ：
Absolute Maximum Ratings at Ta=25
(TA＝25℃)
| Parameter | Part No. | Symbol | Value | Unit | |
| Power Dissipation | Pd(max.) | 60 | MW | *1 | |
| Peak Forward Current | If (max.) | 30 | mA | *1 | |
| (1/10 Duty Cycle,0.1ms Pulse Width)（1/10，0.1ms） | |||||
| Continuous Forward Current | If (Typ.) | 20 | mA | *2 | |
| case temperature | Tp | 120 | ℃ | *3 | |
| LED junction temperature | Tj | 120 | ℃ | ||
| Reverse Voltage | Vr | -8 | V | ||
| Thermal Resistance, junction to case ， | LAMP | RѲ j-c | 0.06 | °C/W | |
| Soldering Temperature ℃ | 5 seconds, 260°C or lower | ||||
| Operating temperature range | Topr | -30℃ to + 80℃ | |||
| Storage Temperature Range | Tstg | -40℃ to + 100℃ | |||
Electro-optical characteristics at Ta=25℃
Ta＝25℃
| Parameter | Part No. | Symbol | Test Condition | Min | Typ | Max. . | Unit |
| Color Rendering | CRI Ra | I f=20mA | 95 | 100 | |||
| Color Quality Scale | CQS Qa | I f=20mA | 95 | 100 | |||
| Fidelity | Rf | I f=20mA | 95 | 100 | |||
| Gamut | Rg | I f=20mA | 95 | 100 | |||
| Television Lighting Consistency Index of 99 99 | TLCI | I f=20mA | 95 | 100 | |||
| Viewing Angle | 2θ1/2 | I f=20mA | 45 | deg | |||
| Forward Voltage | V f | I f=20mA | 2.7 | 3.0 | v | ||
| Reverse Current | I r | V r =8V | 10 |
| |||
| Color Temperature-3200K -3200 K | CCT | I f=20mA | 3000 | 3200 | 3400 | K | |
| Luminous flux | ф | If =20mA | 7 | 8 | 9 | LM | |
| Color Temperature-5600K -5600 K | CCT | I f=20mA | 5300 | 5600 | 5900 | K | |
| Luminous flux | ф | If =20mA | 7 | 8 | 9 | LM | |
*1. Input power and forward current are the values per LED package when the LED is used within the
range of the derating curve in this data sheet and the same amount of current is applied to each channel
*2. Refer to 3. Outline drawing for Tc measurement point.
*3. D.C. Current : Tj = Tp + Rj-c × Pd
D.C.：TJ= TP+RJ-C×PD
Relative Spectral Power Distribution
Relative intensity distribution
Electrical Characteristics
To keep Tp temperature lower than rating enough heat-radiation performance needs to be secured by using an
TP，
adequate heat sink.
Chromaticityranktable
| Color Region | Norninal CCT CCT | Center Point(x,y) （x，y） |
| naturally white | 3200K | (0.4 234 ,0.3990) |
| 4000K | ( 0.38 18,0.3797) | |
| White light | 5000 | ( 0.3446,0.3551) |
| 5600K | (0.32 87 ,0.3 417) |
Reliability Test
Test Items
| Test Items | Test Condi tions | Test hours/Cycles / |
| Room Temperature life test | 25℃ IF=Max | 1000h |
| High Temperature life test | 85℃, 85％ RH, DC Derating IF=Max | 1000h |
| Low Temperature life test | -40℃, DC Derating IF=Max | 1000h |
| High Temperature life test | 85℃, DC 20mA | 1000h |
| High Temperature Storage | 120℃ | 1000h |
| Low Temperature Storage | -40℃ | 1000h |
| Thermal shock | -45℃/150min→125℃/15min Temperature changes in 5min. | 200cycles |
| Temperature Cycle on/off test / | -40/85℃ ,each 20min, 100min transfer Power On/off each 5min , DC 20mA | 100cycles |
| Temperature humidity Cycle Storage | -10℃↔25℃, 95％RH↔85℃, 95％RH [24h/1Cycle] | 100cycles |
| Vibration | 20~80Hz(Displacement:0.06inch, Max 20G) 80~2KHz (Max 20G) Min. Frepuency↔Max. Frepuency 4Min transfer | 4 times |
| Shock | 1500G ,0.5ms, Every 6faces (3axis X 2faces) | 5 times |
| Sale t Spray T | 35℃, salt water 5％ 8h spray→16h leaving alone | 2 cycles |
| Welding instruction Guideline for Soldering (1) 1 . Hand Soldering A soldering iron of less than 20W is recommended to be used in Hand Soldering. Please keep the temperature of the soldering iron under 300℃ while soldering. Each terminal of the LED is to go for less than 3 second and for one time only. Be careful because the damage of the product is often started at the time of the hand soldering. 2 Reflow Soldering: Use the conditions shown in the under Figure of Pb-Free Reflow Soldering.
Reflow soldering should not be done more than two times. Stress on the LEDs should be avoided during heating in soldering process. After soldering, do not deal with the product before its temperature drop down to room temperature. | ||||
| Guideline for Soldering (2) Cleaning It is recommended that alcohol be used as a solvent for cleaning after soldering. Cleaning is to go under 30℃for 3 minutes or 50℃for 30 seconds. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Ultrasonic cleaning is also an effective way for cleaning. But the influence of Ultrasonic cleaning on LED depends on factors such as ultrasonic power. Generally, the ultrasonic power should not be higher than 300W. Before cleaning, a pre-test should be done to confirm whether any damage to LEDs will occur. Note: This general guideline may not apply to all PCB designs and configurations of all soldering equipment. The technics in practise is influenced by many factors, it should be specialized base on the PCB designs and configurations of the soldering equipment. | ||||
| Precautions (1) 1： Storage Moisture proof and anti-electrostatic package with moisture absorbent material is used, to keep moisture to a minimum. Before opening the package, the product should be kept at 30℃ or less and humidity less than 60% RH, and be used within a year. After opening the package, the product should be stored at 30℃ or less and humidity less than 10%RH, and be soldered within 24 hours (1 day). It is recommended that the product be operated at the workshop condition of 3 0℃ or less and humidity less than 60%RH. If the moisture absorbent material has fade away or the LEDs have exceeded the storage time, baking treatment should be performed based on the following condition: (80±5)℃ for 24 hours. 2： Static Electricity Static electricity or surge voltage damages the LEDs. Damaged LEDs will show some unusual charactistics such as the forward voltage becomes lower, or the LEDs do not light at the low current., even not light. All devices, equipment and machinery must be properly grouded. At the same time, it is recommended that wrist bands or anti-electrostatic gloves, anti-electrostatic containers be used when dealing with the LEDs. 8 | ||||
| 3： Design Consideration In designing a circuit, the current through each LED must not exceed the absolute maximun rating specified for each LED. In the meanwhile, resistors for protection should be applied, otherwise slight voltage shift will cause big current change, burn out may happen. It is recommended to use Circuit A which regulates the current flowing through each LED rather than Circuit B. When driving LEDs with a constant voltage in Circuit B, the current through the LEDs may vary due to the variation in Forward Voltage (VF) of the LEDs. In the worst case, some LED may be subjected to stresses in excess of the Absolute Maximum Rating. Thermal Design is paramount importance because heat generation may result in the Characteristics decline, such as brightness dcreased, Color changed and so on. Please consider the heat genertion of the LEDs when making the system design.
| ||||
| 4： When handling the product, touching the encapsulant with bare hands will not only contaminate its surface, but also affect on its optical charactistics. Excessive force to the encapsulant might result in catastrophic failure of the LEDs due to die breakage or wire deformation. For this reason, please do not put excessive stress on LEDs, especially when the LEDs are heated such as during Reflow Soldering. The epoxy resin of encapsulant is fragile, so please avoid scratch or friction over the epoxy resin surface. While handling the product with tweezers, do not hold by the epoxy resin, be careful. 5 Safety Advice For Human Eyes LED ，， LED，。 Viewing direct to the light emitting center of the LEDs, especialy those of great Luminous Intensity, will cause great hazard to human eyes. Please be careful. 6. Some seals and adhesive material containing corrosive substances, such as acetic acid-type glass glue,the use of such materials may lead to changes in light color drift and other optical indicators ,So it should be banned.
| ||||
| Static : 1. This product is a semiconductor light-emitting electronic products sensitive to static electricity. In the process of fixed installation shall prevent static electricity. Wrist strap antistatic bracelet Anti-static gloves Anti-static work clothes are all necessary..Besides, Must ensure that the production line installation workstation, testing equipment ,Transfer units etc grounding is good.Pls add electrostatic protection circuit or device in the driver part if it’s necessary. 2. Power supply LED is a current-driven devices,please use the constant current power supply. Drive current can not exceed the maximum current value in the specification datasheet.. | ||||
English 
Spanish 
French 
Portuguese 
Italian 
